ALERT! Spoofing and fake emails concerning payments – read carefully!

Pixsys
  • Products
    • Controllers - Indicators
      • Entry level
      • Advanced
      • DIN rail
      • Indicators - Panel meters
    • Timers - Counters
    • Process controllers
    • Programmable logics
      • HMI CODESYS
      • PLC
      • HMI + Soft PLC LogicLab
    • I/O Modules
      • Plug-in I/O
      • Remote I/O
    • Operator Panels
      • HMI
      • Web Panel
      • Panel PC
    • Converters - Gateways
      • Signal converters
      • Serial /Protocol converters
      • Modem IIoT
      • VPN Gateway
    • Network Analyzers
      • Current transformer
      • Single-phase network analyzer
      • Three-phase network analyzer
    • Sensors
      • Temperature sensors
      • Infrared sensors
      • Pressure transmitters
      • MELT Pressure transducers
      • Humidity transmitters
    • Actuators
      • SSR
      • Inverters
    • Software and solutions
      • MyPixsys App
      • Programming software Controllers/Indicators
      • CODESYS
      • PLC LogicLab tool
      • HMI Movicon graphics tool
      • Monitoring/recording software
    • General
      • End-of-Life products
      • Discontinued products
      • Accessories
  • Applications
  • Pixsys
  • News
  • Support
  • Contacts
  • Reserved Area
Search in:
    • English
    • Italiano
    English
    • Home
    •   /  
    • En
    •   /  
    • Process controllers cycle programmers
    •   /  
    • Atr902

    ATR902 | Hand-held Process controller

    ATR902 is a hand-held programmer specifically designed for automating small hobby or professional kilns often used in ceramics firing , glass fusing or goldsmithing.

    ATR902 allows the programming of 15 cycles/curves with time-dependent temperature control. Each cycle can contain up to 18 steps/segments, all freely configurable by the user as up/down/down.

    Cycle programming and visualisation are simple and intuitive, even for non-expert operators.

    Typical furnace control software functions are provided: Delayed Start, End-of-Step Wait (in case of process delay at the programmed setpoint) and Cycle Recovery Mode (after any power failure).

    The multi-pin connector, which is also compatible with the previous ATR900/901 series, allows the user to make an immediate connection/installation. The pin-out specifications are detailed in the documentation and allow manufacturers to correctly set up the corresponding connector on the oven.

    The input is programmable for the most common thermocouples and there are two selectable outputs as control or alarm/auxiliary.

    All options are configurable from the keypad (probe type, alarm mode, cycle programming).

    Request Information →

    Request Information

    ×

    • Man. Inst. IT/EN/DE/FR/ES
    to unlock downloads ACCEPT COOKIES
    • Dimensions
      120 x 65 (front panel) x 65 mm
    • Material
      Box: PC UL94V2 self-extinguishing, Front panel: PC UL94V2
    • Weight
      Approx. 550 g
    • Sealing
      Front panel: IP54, Box and terminal blocks: IP20
    • Operating conditions
      Temperature 0-45 °C, humidity 35..95 RH%
    • Certifications
      CE

    ORDERING CODES

    ATR902-12ABC

    Power supply

    24..230 V AC / DC ±15% 50/60 Hz - galvanic isolation 2,5KV

    Power consumption

    3 Watt/VA

    Display

    Display 4 digit 0,56" red + 4 digit 0,4" green + Bargraph

    Analogue inputs

    1 x Ris. 16bit, programmable for K, S, R, J ,T , E, N (automatic compensation of the cold junction 0..50°C, precision @25°C ±0,2% F.S. ±1 digit F.S.)

    Sampling time

    Programmable up to 2,1 ms (frequency up to 470 Hz)

    Digital inputs

    -

    Relais output

    2 x Relais 1A - 250VAC resistive load (with output signal from supply voltage)

    • Control algorithms
      ON - OFF with hysteresis, P., P.I., P.I.D., P.D. time proportional
    • Tuning
      Manual, Automatic predictive
    • Alarm mode
      Absolute / Threshold, band, High / Low deviation, timed auxiliary programmable on single steps
    • Software parameter configuration
      Memory Card, software MyPixsysLab, codes EASY-UP - Programming via APP (NFC) "MyPixsys" for Android and Ios devices
    • Software protections
      Lock of control / alarm setpoint / Access to parameters by password
    installazione_palmare_ATR902
    • ATR902-12ABC
      PLUG-IN PROGRAMMER/TEMP. CONTR.15 CYCLES
      link locator link pixsys link shop
    • ACCESSORIES' CODES
    • 0400.70.001
      KIT HARTING 8P ATR902
    • NET200 | Serial converter

      NET200 | Serial converter

    Discover Related Products:
    Adapters and Cover plates

    Adapters and Cover plates

    Discover
    DIN Rail mounting kit

    DIN Rail mounting kit

    Discover
    Thermocouples

    Thermocouples

    Discover
    pixsys

    Via Po, 16
    30030 - Mellaredo di Pianiga (VE)
    Italy
    Ph. +39 041 5190518 
    Mail: info@pixsys.net

    • COMPANY

      • About us
      • News
      • Applications
    • SUPPORT

      • Real time support
      • Technical FORUM
      • Video tutorials
    Privacy Policy Contacts
    REA PD 362721 - VAT no. IT04111740280 - Suppliers PEC: pixsyssrl_fornitori@pec.it
    Copyright © Pixsys 2025. All Rights Reserved.
    Back to top
    Iris _